access-mech

メカニカルアクセサリー

Mounting Bars

for compact microphones

for modular microphones

for A/B

Flanged Mounting Adapter with Internal Shock Mount AF 1 & Threaded Adapter
ST 20-3/8 & STR-TC
This convenient elastic suspension device accepts any 20 mm diameter microphone or accessory (such as a gooseneck), and holds it in place with a clamp.
For use with our miniature accessories, an adapter (ST 20-3/8) is available with 20 mm outer diameter and 3/8" threading. It has a hole drilled in the center of its top which could be used to pass a miniature cable through, but this would require unsoldering and resoldering the cable connector; two notches are also provided on the sides of the adapter so that this soldering work is generally not required (with one exception: the connector used at the amplifier end of Colette Active Tubes RC KC won't fit through the 20 mm opening).

Dimensions: flange: 69 mm diameter
cylinder: 54 mm diameter,
29 mm depth below the flange

The adapter ST 20-3/8 must be ordered separately.
Color (cylinder and adapter): black

　
　

Vertical Support Rods
STR 250g, 350g, 600g, 1000g
These support rods have complementary 3/8" threads on each end and can thus be screwed together in any combination to extend one another. They can also be attached to the floor stand BF 250.
A gray plastic cap is provided to allow covering the upper threads of an STR if desired.

Lengths: 250 mm, 350 mm, 600 mm, 1000 mm
Diameter: 12 mm
Wrench size for tightening the rods (via flat spots at the lower end): 10 mm
Surface finish: matte gray

　
　

Stand Connector
RG 8
The RG 8 connects an 8 mm tube (e.g. RC or RL) with an STR vertical support rod or any other rod with12 mm in diameter. The angle may be adjusted over a wide range.

The RG 8 is included with the RC and RL tubes.
Color: gray

　
　

Stand Connector
RG 12
The RG 12 connects two STR vertical support rods or any other rods with 12 mm in diameter. The angle may be adjusted over a wide range.
Maximum length of the angled rod when a CMC is fixed at the end and when no counterweight is used: appr. 50 cm

Surface finish: matte gray

　
　

Stand Support Clamp for a Microphone Amplifier
K 20 STR
With this clamp a CMC microphone amplifier can be mounted onto an STR vertical support rod or any other rod 12 mm in diameter. This is especially useful for RC KC tubes of the Colette Modular System whose flexible cable attaches to a CMC amplifier.
Color: gray

　
　

Clamp for VST 62 IUg
K 30 STR
This clamp for the VST 62 IUg stereo microphone amplifier module (30 mm diameter) can be mounted onto an STR vertical support rod or any other rod 12 mm in diameter.
Color: gray

　
　

Table Mounting Flange
F 5g
The F 5g is mounted on a table top with a screw.
It allows the attachment of accessories with 3/8" internal threads. It can also be used with a thread adapter to support any stand adapter or shock mount with 5/8"-27 threads.

Dimensions: height (without threaded stud): 6 mm
diameter: 36 mm
Color matte gray

　
　

Universal Clamp
Z 10
The Z 10 allows microphones or accessory parts to be mounted onto the edge of a table or the like. Two interchangeable pieces can be locked into its hollow handle: a rigid stud with 3/8" threads, for use with additional extensions or accessories, and a two-piece extendable rod with a ball-and-socket head with 3/8" thread.

Maximum thickness of table edge, etc.: 65 mm
Surface finish: black crackle finish

　
　

Heavy Table Stand
T 5g

with 3/8" threaded stud, e.g. for STR support rods

Dimensions: diameter: 129 mm, height: 52 mm
Weight: 1.5 kg
Surface finish: matte gray

　
　

Heavy Floor Stand
BF 250
The BF 250 is supplied with a special chuck, type SPV 12-3/8, to create a quick connect and disconnect system for an STR vertical support rod. This can simply be plugged into the chuck and tightened by hand with a half turn of the milled cap nut.
The chuck SPV 12-3/8 is also available separately for the purpose of updating older equipment. It can be screwed on with a open-ended wrench.

Diameter: 250 mm, height (without the SPV): 38 mm
Weight: approximately 5 kg
Surface finish: black textured varnish

　
　

Special Foam Mat
SM 270

additional isolation against vibration for BF 250

Occasionally a microphone must be placed on a very “noisy” wooden floor, which can lead to pickup of footstep noise, and ? especially when an RC Active Tube is used ? even some mechanical “ringing.” Sometimes the existing acoustic isolation of the heavy floor stand BF 250 does not suffice to keep the microphone free of these disturbances. For that reason we offer the SM 270, an isolation mat which is simply placed beneath the BF 250. It is made of a specially-treated foam material that is very well able to hold its shape.

Dimensions: diameter: 270 mm, thickness: 12 mm
Color: blue-green

| INDEX | HOME PAGE |

Flanged Mounting Adapter with Internal Shock Mount AF 1 & Threaded Adapter ST 20-3/8 & STR-TC This convenient elastic suspension device accepts any 20 mm diameter microphone or accessory (such as a gooseneck), and holds it in place with a clamp. For use with our miniature accessories, an adapter (ST 20-3/8) is available with 20 mm outer diameter and 3/8" threading. It has a hole drilled in the center of its top which could be used to pass a miniature cable through, but this would require unsoldering and resoldering the cable connector; two notches are also provided on the sides of the adapter so that this soldering work is generally not required (with one exception: the connector used at the amplifier end of Colette Active Tubes RC KC won't fit through the 20 mm opening). Dimensions: flange: 69 mm diameter cylinder: 54 mm diameter, 29 mm depth below the flange The adapter ST 20-3/8 must be ordered separately. Color (cylinder and adapter): black

Vertical Support Rods STR 250g, 350g, 600g, 1000g These support rods have complementary 3/8" threads on each end and can thus be screwed together in any combination to extend one another. They can also be attached to the floor stand BF 250. A gray plastic cap is provided to allow covering the upper threads of an STR if desired. Lengths: 250 mm, 350 mm, 600 mm, 1000 mm Diameter: 12 mm Wrench size for tightening the rods (via flat spots at the lower end): 10 mm Surface finish: matte gray

Stand Connector RG 8 The RG 8 connects an 8 mm tube (e.g. RC or RL) with an STR vertical support rod or any other rod with12 mm in diameter. The angle may be adjusted over a wide range. The RG 8 is included with the RC and RL tubes. Color: gray

Stand Connector RG 12 The RG 12 connects two STR vertical support rods or any other rods with 12 mm in diameter. The angle may be adjusted over a wide range. Maximum length of the angled rod when a CMC is fixed at the end and when no counterweight is used: appr. 50 cm Surface finish: matte gray

Stand Support Clamp for a Microphone Amplifier K 20 STR With this clamp a CMC microphone amplifier can be mounted onto an STR vertical support rod or any other rod 12 mm in diameter. This is especially useful for RC KC tubes of the Colette Modular System whose flexible cable attaches to a CMC amplifier. Color: gray

Clamp for VST 62 IUg K 30 STR This clamp for the VST 62 IUg stereo microphone amplifier module (30 mm diameter) can be mounted onto an STR vertical support rod or any other rod 12 mm in diameter. Color: gray

Table Mounting Flange F 5g The F 5g is mounted on a table top with a screw. It allows the attachment of accessories with 3/8" internal threads. It can also be used with a thread adapter to support any stand adapter or shock mount with 5/8"-27 threads. Dimensions: height (without threaded stud): 6 mm diameter: 36 mm Color matte gray

Universal Clamp Z 10 The Z 10 allows microphones or accessory parts to be mounted onto the edge of a table or the like. Two interchangeable pieces can be locked into its hollow handle: a rigid stud with 3/8" threads, for use with additional extensions or accessories, and a two-piece extendable rod with a ball-and-socket head with 3/8" thread. Maximum thickness of table edge, etc.: 65 mm Surface finish: black crackle finish

Heavy Table Stand T 5g with 3/8" threaded stud, e.g. for STR support rods Dimensions: diameter: 129 mm, height: 52 mm Weight: 1.5 kg Surface finish: matte gray

Heavy Floor Stand BF 250 The BF 250 is supplied with a special chuck, type SPV 12-3/8, to create a quick connect and disconnect system for an STR vertical support rod. This can simply be plugged into the chuck and tightened by hand with a half turn of the milled cap nut. The chuck SPV 12-3/8 is also available separately for the purpose of updating older equipment. It can be screwed on with a open-ended wrench. Diameter: 250 mm, height (without the SPV): 38 mm Weight: approximately 5 kg Surface finish: black textured varnish

Special Foam Mat SM 270 additional isolation against vibration for BF 250 Occasionally a microphone must be placed on a very “noisy” wooden floor, which can lead to pickup of footstep noise, and ? especially when an RC Active Tube is used ? even some mechanical “ringing.” Sometimes the existing acoustic isolation of the heavy floor stand BF 250 does not suffice to keep the microphone free of these disturbances. For that reason we offer the SM 270, an isolation mat which is simply placed beneath the BF 250. It is made of a specially-treated foam material that is very well able to hold its shape. Dimensions: diameter: 270 mm, thickness: 12 mm Color: blue-green